BMW TIS Online
X

Tag: n53

Removing and installing, replacing rear exhaust manifold engine BMW N53

11 40 060 Necessary preliminary work: Remove front underbody protection. Partially detach rear underbody protection Remove complete exhaust system. Note:…

Removing and installing, replacing front exhaust manifold on engine BMW N53

11 40 050 Necessary preliminary work: Remove rear exhaust manifold. Note: The oxygen sensors are in danger of being damaged…

Removing and installing or replacing coolant thermostat engine BMW N53

11 53 000 Special tools required: 17 2 052 Warning! Risk of scalding! Only perform this work after engine has…

Removing and installing cylinder head engine BMW N53

11 12 100 Important! Aluminium‐magnesium materials. No steel screws/bolts may be used due to the threat of electrochemical corrosion. A…

Checking cylinder head for watertightness engine BMW N53

11 12 729 Secure special tool 11 4 341 to cylinder no. 1 with special tool 11 4 345 Tightening…

Replacing crankshaft radial shaft seal engine BMW N53

11 14 151 Important! Magnet wheel (1) is magnetic. Keep magnet wheel (1) in a plastic bag away from swarf.…

Removing and installing or replacing vacuum pump on engine BMW N53

11 66 000 Necessary preliminary tasks: Remove drive belt. Remove tensioner for drive belt. Remove sealing cover for vacuum pump.…

Adjusting camshaft timing engine BMW N53

11 31 505 Important! Risk of damage! To open the central bolt at the camshaft, grip hexagon head on rear…

Resurfacing cylinder head sealing face on engine BMW N53

11 12 719  Important! Postwork on cylinder head maximum of 0.3 millimetres Necessary preliminary tasks: Disassemble cylinder head. Check evenness…

Replacing all valve springs on engine BMW N53

11 34 715  Special tools required: 11 0 009 11 4 480 11 9 000 11 9 017 11 9…

Removing and installing or replacing chain module for oil pumpm, vacuum pump on engine BMW N53

11 41 010 Important! Aluminium‐magnesium materials. No steel screws/bolts may be used due to the threat of electrochemical corrosion. A…

Replacing piston rings on all pistons on engine BMW N53

11 25 671  Necessary preliminary work: Remove all pistons. Measuring side clearance of piston rings in piston ring groove. Technical…

Replace all connecting rod bearings on engine BMW N53

11 24 571  Special tools required: 00 2 590 00 9 120 Important! All crank pins are connected with the…

Removing and installing, replacing both lambda oxygen monitoring sensors engine BMW N53

11 78 545 Warning! Risk of burning! Only perform these tasks after the exhaust system has cooled down. Installation note:…

Removing and installing engine BMW N53

11 00 050 Special tools required: 11 0 000 11 7 310 13 5 281 13 5 282 00 9…

Replacing tensioning device for alternator drive belt on engine BMW N53

11 28 020 Special tools required: 11 3 340 Necessary preliminary work: Remove drive belt. Remove special tool 11 3…

Replacing all valve stem seals engine BMW N53

11 34 560  Special tools required: 11 1 480 11 6 380 Necessary preliminary tasks: Remove cylinder head. Remove intake…

Disassembling and assembling cylinder head – cylinder head removed engine BMW N53

11 12 503  Fit cylinder head on special tool 11 9 000 . Insert special tools 11 9 006 and…

Removing and installing, sealing or replacing oil sump engine BMW N53

11 13 000  Important! Aluminium screws/bolts must be replaced each time they are released. The end faces of aluminium screws/bolts…

Sealing crankcase lower section engine BMW N53

11 21 505 Important! Aluminium‐magnesium materials. No steel screws/bolts may be used due to the threat of electrochemical corrosion. A…

This website uses cookies.