BMW TIS Online
X

m50tu

Removing and installing cyliner head on engine BMW M50 VANOS

11 00 Remove intake manifold together with throttle valve. This step will have already been carried out on engines which…

Removing vibration-damper hub on engine BMW M50 VANOS

11 00 Hold flywheel with Special Tool 11 2 170. Unscrew central bolt. Take off washer and hub. Installation: Position…

Removing oil pan on engine BMW M50 VANOS

11 00 Unscrew and pull out oil dipstick guide tube. Installation: Check sealing ring, replacing if necessary. Unscrew all bolts…

Replacing front radial sealing ring on engine BMW M50 VANOS

11 00 Fit special tool 11 2 383 to crankshaft. Removing radial sealing ring: Screw on special tool 11 2…

Removing vibration damper on engine BMW M50 VANOS

11 00 Arrest engine with special tool 11 2 170. Caution! Do not use a mandrel to hold the engine.…

Removing oil pump on BMW E36 with engine M50 VANOS

11 00 Unscrew nut for sprocket. Caution! Left-hand threads. For tightening torque, refer to Technical Data Lift off sprocket with…

Checking operation of VANOS on engine BMW M50

11 36 000 Interrogate fault memory of engine control unit. VANOS control unit connector is located behind oil filter and…

Replacing camshaft on engine BMW M50 VANOS

11 31 001 (Intake or exhaust side, as applicable) The intake and exhaust camshafts can be changed in the vehicle.…

Replacing piston cooling-spray jets on engine BMW M50 VANOS

11 00 Note: Spray jets are installed in bores of thrust bearings 2 ... 7 and serve to lubricate piston…

Removing crankshaft on engine BMW M50 VANOS

11 00 Fit special tool 11 2 383 to crankshaft. Remove sprocket with special tool 11 2 000 in conjunction…

Removing lower timing chain and guides on engine BMW M50 VANOS

11 00 Fold tensioning rail in downwards direction. Lift out timing chain. Remove tensioning rail. Removing Chain Guide: Lift upper…

Replacing thermostat housing cover on engine BMW M50 VANOS

11 00 If applicable, unscrew thermostat housing for other work on cylinder head later. Installation: Sealing surfaces must be clean…

Adjusting instructions for camshaft on engine BMW M50 VANOS

11 00 Secure crankshaft in the TDC setting with special tool 11 2 300. Important! Remove alignment pin before starting…

Removing cylinder head cover on engine BMW M50 VANOS

11 00 If applicable, pull connectors off ignition coils. Unscrew nuts. Remove ignition coils. Installation: Check for earth strap of…

Disassembling and assembling cylinder head, mounting cylinder head on assembly fixture for engine BMW M50 VANOS

11 00 Fit special tool 11 1 065 to special tool 00 1 490. Do not install special tool 11…

Removing tensioning roller and console on engine BMW M50 VANOS

11 00 Unscrew tensioning roller. Unscrew mounting block. Note: The hydraulic belt tensioner is filled with oil, so that a…

Checking, replacing 4/2-way valve for VANOS on engine BMW M50

11 36 550  (Solenoid valve) (Refer to Operation No. 11 36 000) Switch off ignition. VANOS control unit connector is…

Replacing guide bearing in crankshaft on engine BMW M50TU (VANOS)

11 00 Remove thrust bearing with special tool 11 2 340. Installation: Install new thrust bearing and drive firmly home…

Checking function of VANOS on engine BMW M50

11 00 Crank engine in direction of rotation until cam peaks of intake and exhaust cams in cylinder No. 1…

Mounting engine on assembly stand BMW M50 VANOS

11 00 Unscrew exhaust manifold. Unscrew nuts. Lift off exhaust manifolds. Installation: Shorter manifold is at rear. Replace nuts. Coat…

This website uses cookies.