BMW TIS Online
X

crankshaft

Replacing crankshaft on on engine BMW N63O1

11 21 500  Attention! Weight of crankshaft is approx. 25 kg. Risk of injury from sharp edge of housing. Necessary…

Replacing crankshaft on engine BMW N63

11 21 500  Attention! Weight of crankshaft is approx. 20 kg. Risk of injury from sharp edge of housing. Installation…

Replacing all crankshaft main bearing shells on engine BMW N63 (without hybrid drive)

11 21 531 Important! Risk of injury from sharp edge of housing. Important! If a crankcase or a crankshaft is…

Replacing crankshaft radial seal on transmission side on engine BMW N63

11 14 151  Important! The radial crankshaft seal can only be replaced completely with the end cover. The radial crankshaft…

Replacing main crankshaft bearing shell on engine BMW M73

11 21 531  (engine dismantled) Clean components before installing. Preparations are described under heading "Replacing crankshaft", refer to 11 21…

Replacing crankshaft on engine BMW M73

11 21 500  (engine removed) Remove lower timing case, refer to 11 14 115 Remove piston, refer to 11 25…

Replacing crankshaft radial sealing ring on engine BMW M73

11 14 151  (Transmission side) Remove transmission. Drain engine oil. This operation is described in section on BMW engine oil…

Removing crankshaft on engine BMW M50 VANOS

11 00 Fit special tool 11 2 383 to crankshaft. Remove sprocket with special tool 11 2 000 in conjunction…

Removing crankshaft on engine BMW M50

11 00 Replace crankshaft, refer to 11 21 501 Remove main-bearing covers (1 ... 7) and lift out crankshaft. Installation:…

Replacing guide bearing in crankshaft on engine BMW M50TU (VANOS)

11 00 Remove thrust bearing with special tool 11 2 340. Installation: Install new thrust bearing and drive firmly home…

Replacing spray jets in crankshaft bearing supports on engine BMW M50

11 00 Note: Spray jets are installed in bores of crankcase for bearings 2-7 and supply oil for lubrication of…

Replacing crankshaft pulse sensor on engine BMW S55

12 14 521  Important! Read and comply with notes on protection against electrostatic discharge (ESD protection). Necessary preliminary work: Remove…

Replacing crankshaft radial seal (transmission side) on engine BMW M40, M42, M43, M43TU, M44, M50, M52, M52TU, M54, M56, S52, S54

11 14 151 Note: This repair instruction is valid for the following engines: BMW M40, M42, M43, M43TU, M44, M50, M52,…

Replacing pilot bearing in crankshaft engine BMW M50

11 00 603  Remove pilot bearing with special tool 11 2 010 or 11 2 340. Installation: Install pilot bearing…

Replacing crankshaft on engine BMW M50 – crankshaft removed

11 21 501  Note: Replacement crankshafts are supplied complete with corresponding main and connecting-rod bearing shells. Crankshaft identification cast on…

Crankshaft and Bearings BMW M50B25 VANOS

11 21 Ground sizes of main bearing journals Standard yellow mm 59.984 ... 59.990 Standard green mm 59.977 ... 59.983…

Replacing crankshaft radial sealing ring on engine BMW M60

11 14 151  (Transmission side) Remove transmission. Drain engine oil. This operation is described in section on BMW engine oil…

Replacing rear radial crankshaft seal on transmission side on engine BMW S55

11 14 151 Important! Magnet wheel (1) is magnetic. Keep magnet wheel (1) in a plastic bag away from swarf.…

Replacing main crankshaft bearing shell on engine BMW M60

11 21 531  (Engine dismantled) Clean components before installing. Preparations are described under heading "Replacing crankshaft", refer to 11 21…

Replacing all crankshaft main bearings on engine BMW S85

11 21 531  Important! Repair: crankcase used / crankshaft used. If the bearing channel is opened and closed again after…

This website uses cookies.