BMW TIS Online
X

camshaft

Replacing pulse generator for inlet camshaft on engine BMW S62

12 14 523  Interrogate fault memory of DME control unit. Switch off ignition. The instructions apply to removing and installing…

Replacing left camshaft (cylinder bank 7-12) on engine BMW M73

11 31 011  Remove both cylinder head covers, refer to 11 12 004 Remove all spark plugs, refer to 12 12…

Checking timing of camshaft(s) on engine BMW M73

11 31 005  Remove both cylinder head covers, refer to 11 12 004 Removing spark plugs, refer to 12 12…

Adjusting camshaft timing on engine BMW M73

11 31 505  (re Oper. No. 11 31 005) Before carrying out adjustment work, the camshaft timing must be checked,…

Replacing camshaft on engine BMW M50 VANOS

11 31 001 (Intake or exhaust side, as applicable) The intake and exhaust camshafts can be changed in the vehicle.…

Removing camshaft on engine BMW M50

11 00 ...  Attention! Camshafts could be pre-damaged or broken when removal/installation were performed incorrectly without a fixture. In addition,…

Adjusting instructions for camshaft on engine BMW M50 VANOS

11 00 Secure crankshaft in the TDC setting with special tool 11 2 300. Important! Remove alignment pin before starting…

Replacing camshaft on engine BMW M50 (intake or exhaust side as applicable)

11 31 001 Lift engine hood into assembly position and remove firewall (air manifold). This work is described in section…

Replacing pulse sensor on exhaust camshaft BMW S55

12 14 524  Important! Read and comply with notes on protection against electrostatic discharge (ESD protection). Necessary preliminary tasks: Read…

Adjustment specification for camshaft on engine BMW M50

11 00 Hold crankshaft in TDC position with Special Tool 11 2 300. Caution! Remove special tool prior to operating…

Replacing pulse sensor on intake camshaft engine BMW S55

12 14 523  Important! Read and comply with notes on protection against electrostatic discharge (ESD protection). Necessary preliminary tasks: Read…

Replacing camshaft impulse transmitter (breakerless ignition distribution) engine BMW M50

12 14 525 Switch off ignition. Function description, Bosch DME Design: Inductive sensor Detects only the speed of the camshaft.…

Removing and installing, replacing intake camshaft on engine BMW S55

11 31 025 Necessary preliminary work: Remove cylinder head cover. Remove intake adjuster. Remove intermediate lever. Adjust valve timing. Note:…

Replacing right camshaft on engine BMW M60

11 31 015 (intake or exhaust side as applicable) Cylinder bank 1-4 Remove both cylinder head covers, refer to 11…

Replacing left camshaft on engine BMW M60

11 31 011 (intake or exhaust side as applicable) Cylinder bank 5-8 Remove both cylinder head covers, refer to 11…

Adjusting timing of camshaft(s) engine BMW M60

11 31 010 Remove both cylinder head covers, refer to 11 12 004 Remove all spark plugs, refer to 12…

Checking camshaft timing engine BMW S55

11 31 005 Important! When the engine is shut down, the intake and exhaust camshaft adjusters are normally locked in…

Adjusting timing of camshaft(s) engine BMW S55

11 31 505 Necessary preliminary tasks: Remove cylinder head cover. Check timing. With 1st cylinder in TDC firing position, cams…

Removing and installing or replacing intake and exhaust camshaft adjusters engine BMW S55

11 36 046 Important! Use only special tool 11 4 280 to loosen the central bolts of the VANOS units.…

Removing and installing, replacing right camshaft adjustment unit engine BMW M62 VANOS from 9/1998

11 36 615 Remove intake filter housing with air-mass flow sensor. Remove fan impeller with fan clutch and fan cowl.…

This website uses cookies.