33 32 190

Special tools required:

2 412 505
33 5 013
33 5 014
33 5 015
2 412 506
33 5 016
33 5 020
33 5 017
2 358 630

Note:

If the camber arm is detached from the rear axle support/wheel carrier, it is necessary after installation to carry out a wheel alignment.

Necessary preliminary tasks:

Remove rear wheel.

Removal:

Removing and installing, replacing left or right camber arm BMW M2 F87

Left only:

Slacken nut (1).

Release jointed rod (2) from camber control arm.

Removing and installing, replacing left or right camber arm BMW M2 F87

Secure camber control arm and spring against falling off.

Undo nut (3) and unscrew eccentric bolt (2).

Undo nut (4) and unscrew bolt (5).

Undo nut (7) and unscrew bolt (6).

Remove camber control arm (1):

Installation:

Note:

The screw connections for camber control arm on rear axle support and shock absorber on camber control arm must be tightened in normal position. For this purpose, the coil spring must be tensioned.

Removing and installing, replacing left or right camber arm BMW M2 F87

Position camber control arm (1).

Part: Renew bolts (5 and 6) and nuts (3, 4 and 7).

Insert bolt (6).

Screw on the nut (7).

Do not tighten screw connection to torque yet.

Insert eccentric bolt (2).

Fit eccentric washer and tighten nut (3).

Tightening torque 33 32 8AZ:

8AZ Camber control arm to wheel carrier
F80 / F82 / F83 / F87 M14 Renew nut. 165 Nm

Insert bolt (5).

Screw on the nut (4).

Do not tighten screw connection to torque yet.

Installation note:

Note direction of insertion of bolts.

Removing and installing, replacing left or right camber arm BMW M2 F87

Insert lower spring cup 2 412 505 centrally into coil spring and turn to lowest winding.

Guide spindle 33 5 013 , 33 5 014 , 33 5 015 from below through the camber link and the lower spring cup 2 412 505.

Removing and installing, replacing left or right camber arm BMW M2 F87

Insert top spring cup 2 412 506 sideways into coil spring and turn to the uppermost winding.

Important!

Make sure spindle (hexagonal) is correctly seated in upper spring cup 2 412 506 !

Pull spindle 33 5 013 down.

Removing and installing, replacing left or right camber arm BMW M2 F87

Warning!

Danger of injury!

Make sure coil spring is correctly positioned in spring cups.

Removing and installing, replacing left or right camber arm BMW M2 F87

Important!

Centre special tools 2 412 505 , 2 412 506 , 33 5 013 , 33 5 014 , 33 5 015 to achieve the greatest possible contact surface with the coil spring.

Check installation position of special tools 2 412 505 , 2 412 506 , and 33 5 013 , 33 5 014 , 33 5 015 , correct if necessary.

Removing and installing, replacing left or right camber arm BMW M2 F87

Tighten coil spring using special tools 33 5 016 and 33 5 020 , gripping the spindle of the spring tensioner with special tool 33 5 017 .

Tension the coil spring so that the normal position can be set by lifting the wheel carrier.

Removing and installing, replacing left or right camber arm BMW M2 F87

Secure special tool 2 358 630 with wheel studs to drive flange.

Insert workshop jack into special tool 2 358 630.

Removing and installing, replacing left or right camber arm BMW M2 F87

Adjusting normal position:

Note:

To raise the wheel carrier, the spring absolutely must be tensioned. Do not move the wheel carrier to normal position against the spring force.

Push wheel carrier with workshop jack and special tool 2 358 630 up to dimension A.

Dimension A = middle of wheel hub to upper edge of wheel arch

Dimension A – F80 = 343 mm Dimension A – F82, F83 = 363 mm

Removing and installing, replacing left or right camber arm BMW M2 F87

Tighten nut (7).

Tightening torque 33 32 7AZ:

7AZ Camber control arm to rear axle support
F80 / F82 / F83 / F87 M14 Renew screw and nut.

Tighten down in normal position.

165 

Tighten nut (4).

Tightening torque 33 52 3AZ:

3AZ Shock absorber to camber arm
F80 / F82 / F83 / F87 M12 Renew screw and nut.

Tighten down in normal position.

Jointing torque 100 Nm
Angle of rotation 90 °

Removing and installing, replacing left or right camber arm BMW M2 F87

Lower workshop jack and place to one side.

Remove special tool 2 358 630.

Removing and installing, replacing left or right camber arm BMW M2 F87

Check fitting of coil springs in spring pads (top and bottom), if necessary again align and relieve tension.

Remove special tools 2 412 505 , 2 412 506 , and 33 5 013 , 33 5 014 , 33 5 015.

Removing and installing, replacing left or right camber arm BMW M2 F87

Left only:

Insert jointed rod (2) at camber control arm.

Part: Replace nut (1).

Tighten nut (1).

Tightening torque 37 14 4AZ:

4AZ Jointed rod to ride height sensor and camber arm
F80 / F82 / F83 / F87 M6 Renew nut. 8 Nm

Required follow-up work:

Install rear wheel.
Carry out wheel alignment procedure.