Removing and installing engine BMW B47D

11 00 050

Required tools:
11 0 000

Note:
Refrigerant recirculation from the air-conditioning system is not required!

Necessary preliminary operations:
Disconnect the negative battery cable.
Bring the hood to the maintenance position.
Drain the engine oil.
Remove the gearbox.
Remove both output shafts (all-wheel drive vehicles only).
Remove the drive belt.
Remove the rear soundproof cover.
Remove the electronics compartment.
Disconnect the air conditioning compressor from the generator bracket.
Drain the coolant.
Remove the left pressure pipe.
Remove the right pressure pipe.
Remove particulate filter.

Withdrawal:
Release the seal of the partition in the marked area (1) from the clips.
Unlock and detach connector (2).
Remove the nut (3).
Disconnect the generator cable (4) and the cable (5) from the bulkhead.
Изображение

Unlock coolant pipe (1) and detach coolant from line (2).
Изображение

Unlock vacuum line (1) and detach from vacuum line (2).
Detach vacuum line (2) from bulkhead.
Изображение

Unlock coolant return pipe (1) and detach coolant from coolant pipe (2).
Unlock and disconnect coolant pipe (2) from connecting pipe.
Unlock and detach coolant pipe (2) from radiator.
Unclip the coolant pipe (2) from the clamp (3) and disassemble.
Изображение

Unlock coolant pipe (1) and detach from full flow oil filter.
Изображение

Unlock coolant pipe (1) and disconnect from thermostat.
Unlock coolant pipe (2) and disconnect from thermostat.
Изображение

Unclip fuel lines in clamp (1) and clamp (2) and detach from bracket (4).
Release nuts (3) and remove bracket (4).
Изображение

Unlock and detach fuel line (1).
Unlock and detach fuel return pipe (2).
Изображение

Only cars with automatic transmission:
Unlock and disconnect the transmission oil return pipe (1).
Unlock and disconnect the transmission oil line (2).
Unlock and detach coolant pipe (3).
Изображение

Release nut (1) on left engine mounting cushion.
Изображение

Release nut (1) on right engine mounting cushion.
Изображение

Hang special tool11 0 000 onto the motor stripper.
Suspend special tool 11 0 000 only for mounting lugs (1 and 2) designed for this purpose.
Remove the engine using the engine take-off (3).
Изображение

Installation:

Hang special tool11 0 000 onto the motor stripper.
Suspend special tool 11 0 000 only for the mounting eye (1 and 2) intended for this purpose.
Lift the engine into the vehicle using the engine take-off tool (3).
Изображение

Tighten the nut (1) to the right engine mounting cushion.
The inhaling moment 22 11 2AZ.
Изображение

Tighten the nut (1) to the left engine mounting cushion.
The inhaling moment 22 11 2AZ.
Изображение

Only cars with automatic transmission:
Connect and lock the coolant pipe (3).
Connect and seal the transmission line for the gear oil (2).
Reconnect and secure the transmission oil return pipe (1).
Note:
All piping must be fixed with an audible click.
Изображение

Connect the fuel return pipe (2).
Connect the fuel supply line (1).
Note:
All locks should be locked with an audible click.
Изображение

Install the bracket (4).
Tighten the nuts (3).
Hang fuel lines in clamp (2) and clamp (1).
Изображение

Lock the coolant lines (1 and 2) and connect them to the thermostat. Note:
Both latches should be locked with an audible click.
Изображение

Lock the coolant pipe (1) and connect it to a full-flow oil filter. Note:
The lock should be locked with an audible click.
Изображение
Install and lock the coolant pipe (2) on both sides.
Connect the coolant pipe (2) to the connecting pipe and the radiator.
Lock the coolant return pipe (1) and connect it to the coolant pipe (2).
Note:
All locks should be locked with an audible click.
Hang the coolant pipe (2) in the clamp (3).
Изображение

Suspend the vacuum line (2) on the front cover.
Connect the vacuum line (2) to the vacuum line (1).
Note:
The lock should be locked with an audible click.
Изображение

Lock the coolant pipe (1) and connect it to the coolant pipe (2). Note:
The lock should be locked with an audible click.
Изображение

Hang the cable (5) and the generator wire (4) on the front cover.
Tighten the alternator wire (4) with a nut (3).
Tightening torque 12 52 4AZ.
Connect and secure the connector (2).
Fix the seal of the partition (1) in the clamp.
Note:
Pay attention to the correctness of fixing the seal of the septum in the marked area.
Изображение

Required Fit:
Install the gearbox.
Install the particulate filter.
Install both output shafts (all-wheel drive vehicles only).
Secure the air conditioning compressor.
Fill the coolant.
Install the left pressure pipe.
Install the right pressure pipe.
Install the rear soundproof cover.
Install the drive belt.
Install the electronics compartment.
Fill with engine oil.
Bring the hood cover to the normal position.
Connect the negative battery cable.