35 11 000 

Necessary preliminary tasks:

Remove clutch pedal

Removing and installing complete bearing block for foot pedal BMW 3 E90

Release screws (1) and gently press clutch master cylinder (2) to one side.

Installation:

Line remains connected.

Replace self-locking nuts.

Tightening torque 21 52 4AZ:

Type Thread Tightening specification Torque
1AZ Hydraulic line to clutch slave cylinder or throttle.
E36 / E38 / E39 / E52 / E53 / E60 / E61 / E63 / E64 / E83 / E85 / E86 / E81 / E87 / E90 / E91 / E92 14.5 Nm
E46 20 + 5 Nm
2AZ Clutch master cylinder to bearing support
E36 / E38 / E39 / E46 / E52 / E53 / E60 / E61 / E63 / E64 / E85 / E84 / E86 / E87 / E89 / E90 / E91 / E92 / E93 22 Nm
E83 8 Nm
3AZ Fitting screw, clutch master cylinder
E36 / E38 / E39 / E46 / E52 / E53 / E60 / E61 / E63 / E64 / E83 / E85 / E86 / E87 / E90 / E91 / E92 / E93 22 Nm
4AZ Clutch master cylinder to pedal assembly
E36 / E38 / E39 / E46 / E52 / E53 / E60 / E61 / E63 / E64 / E81 / E82 / E83 / E84 / E85 / E86 / E87 / E88 / E89 / E90 / E91 / E92 / E93 9 Nm
5AZ Clutch slave cylinder to clutch housing/transmission case
E36 / E38 / E39 / E46 / E52 / E53 / E60 / E61 / E63 / E64 / E81 / E82 / E83 / E84 / E85 / E86 / E87 / E88 / E89 / E90 / E91 / E92 / E93 22 Nm
E60 / E63 7-speed SMG 25 Nm
6AZ Pressure accumulator to hydraulic unit
E36 / M3 35 Nm
7AZ Coupling bolts for hydraulic pipes
E46 / M3 14 Nm
8AZ Pressure accumulator for hydraulic unit
E46 / M3 40 Nm
9AZ Clutch position sensor to clutch slave cylinder
E46 / E60 / E61 / E63 / E64 / E85 6-speed SMG 2.5 Nm
E60 / E61 / E63 7-speed SMG 3.5 Nm
10AZ Banjo bolt, pipe, actuator/pump block
E60 / E61 / E63 7-speed SMG 18 Nm
11AZ Filler plug, expansion tank, pump block
E60 / E61 / E63 7-speed SMG 2.1 Nm
12AZ Throttle valve to clutch slave cylinder
E60, E61 17 Nm

Removing and installing complete bearing block for foot pedal BMW 3 E90

Disconnect plug connection (1).

Remove locking clip (2) and pull out pin.

Unscrew nut (3).

Release nuts (4) and gently swivel bearing block to left and remove.

Installation:

Tighten nuts (4) before nut (3).

Replace self-locking nuts.

Tightening torque 35 11 1AZ:

Type Thread Tightening specification Torque
1AZ Bearing pedestal to brake assembly and body
E81, E82, E87, E88, E90, E91, E92, E93, E84 M8 Retighten 1x on brake booster after 5 min 21 Nm
E81, E82, E87, E88, E90, E91, E92, E93, E84 M6 8 Nm