BMW TIS Online
X

11 Engine

Replacing roller bearing for dual-mass flywheel on engine BMW N63

11 22 513 Special tools required: 21 2 051 21 2 052 Note: Flywheel removed! Using hydraulic press (1) and special tool 21 2…

Engine identification (Engine number at the marked surface)

Engine number at the marked surface. Replacement drives are already assigned a number containing the identification and engine number at…

Removing and installing, renewing vibration damper on engine BMW N63

11 23 010  Special tools required: 00 9 140 11 3 460 11 8 090 11 9 453 11 9 454 Necessary preliminary work: Remove fan cowl Remove A/C compressor…

Removing and installing, replacing right intake plenum on engine BMW N63

11 61 068  Necessary preliminary work: Remove right injection pipe. Remove throttle valve Release screws on intake plenum from above…

BMW leakage test for intake system on engine N63O1

11 61 730  Special tools required: 2 358 459 2 359 613 0 426 464 81 31 2 357 800 (bisher: 81 38 2…

Removing and installing, replacing vibration damper on engine BMW N63O1

11 23 010  Special tools required: 00 9 140 11 3 460 11 8 090 11 9 453 11 9 454 Necessary preliminary work: Remove charge air cooler on left…

Removing and installing, renewing oil feed line for exhaust turbocharger BMW N63O1

11 42 200 Necessary preliminary tasks: Remove alternator. Remove both exhaust turbochargers. Remove both exhaust manifolds. Remove heat shield at…

Removing and installing, replacing blow-off valve on engine BMW N63

11 65 165  Necessary preliminary tasks: Follow diagnosis instruction. Remove exhaust turbocharger Release screws (1). Tightening torque 11 65 9…

Removing and installing, replacing left intake plenum BMW N63

11 61 065  Necessary preliminary work: Remove left injection pipe. Remove throttle valve Release screws on intake plenum from above…

Replace oil separator BMW N63O0

11 15 140  Necessary preliminary tasks: Remove cylinder head cover Removal: Release screws in the sequence 3 - 1. Remove…

Replace oil separator BMW N63O1

11 15 140  Necessary preliminary work: Remove cylinder head cover Removal: Release screws in the sequence 4 - 1. Remove…

Removing and installing, replacing servomotor for eccentric shaft (cyl. 1 to 4) BMW N63O1

11 37 020 Necessary preliminary tasks: Remove front axle with engine and transmission. Remove right intake plenum. Attention! Risk of…

Engine oil service BMW S85

11 00 ...  Attention! Perform engine oil service only when engine is at normal operating temperature (>70 °C engine oil…

Removing and installing engine BMW S50

11 00 050 Special tools required: 11 002 0 Follow instructions for disconnecting and connecting battery, refer to general instructions in…

Removing and installing engine BMW N54, N54T

11 00 050 Important! Aluminium screws/bolts must be replaced each time they are released. Aluminium screws/bolts are permitted with and…

Replacing crankshaft on on engine BMW N63O1

11 21 500  Attention! Weight of crankshaft is approx. 25 kg. Risk of injury from sharp edge of housing. Necessary…

Replacing right connecting line on engine BMW N63

11 15 008  Observe Electronic Parts Catalogue! If necessary, individually replace broken connectors (connections) without having to replace all engine…

Checking function of vacuum system on engine BMW N63, (N63 O0 O1)

11 66 521 Attention! Note the sequence of the diagnosis instructions in the ISID: Connect Integrated Measurement Interface Box (IMIB)…

Remove, install, replace engine ventilation line BMW N63

11 15 015 Observe Electronic Parts Catalogue! If necessary, individually replace broken connectors (connections) without having to replace all engine…

Removing and installing engine on front axle (N63O1) with GA8HP70Z allwheel drive vehicle transmission on engine BMW N63

11 00 598  Necessary preliminary tasks: Remove front axle with engine and transmission. Remove propeller shaft from between front axle…

This website uses cookies.